IEEE C63.14:1995—Dictionary for technologies of electromagnetic compatibility (EMC), electromagnetic pulse (EMP), and electrostatic discharge (ESD).

IEEE C95.2:1999—IEEE standard for radio-frequency energy and current flow symbols.

ISO 2315:1994—Two- and four-pole sealed electromagnetic relays, 2 A and 3 A—Clearance and fixing dimensions.

ISO 5066-1:1994—Hermetically sealed monostable electrical relays, 2 A and 3 A—Part 1: Operating characteristics and test conditions.

ISO 5066-2:1994—Hermetically sealed monostable electrical relays, 2 A and 3 A—Part 2: Type approval tests.

ISO 7637-0:1990—Road vehicles—Electrical disturbance by conduction and coupling—Part 0: Definitions and general.

ISO 7637-1:1990—Road vehicles—Electrical disturbance by conduction and coupling—Part 1: Passenger cars and light commercial vehicles with nominal 12-V supply voltage—Electrical transient conduction along supply lines only.

ISO 7637-2:1990—Road vehicles—Electrical disturbance by conduction and coupling—Part 2: Commercial vehicles with nominal 24-V supply voltage—Electrical transient conduction along supply lines only.

ISO 7637-3:1995—Road vehicles—Electrical disturbance by conduction and coupling—Part 3: Vehicles with nominal 12-V or 24-V supply voltage—Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines.

ISO 11451-1:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 1: General and definitions.

ISO 11451-2:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 2: Off-vehicle radiation source.

ISO 11451-3:1994—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 3: On-board transmitter simulation.

ISO 11451-4:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Vehicle test methods—Part 4: Bulk current injector (BCI).

ISO 11452-1:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 1: General and definitions.

ISO 11452-2:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 2: Absorber-lined chamber.

ISO 11452-3:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 3: Transverse electromagnetic mode (TEM) cell.

ISO 11452-4:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 4: Bulk current injection (BCI).

ISO 11452-5:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 5: Strip line.

ISO 11452-6:1997—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 6: Parallel plate antenna.

ISO 11452-7:1995—Road vehicles—Electrical disturbances by narrow-band radiated electromagnetic energy—Component test methods—Part 7: Direct radio-frequency (RF) power injection.

ISO TR 10605:1994—Road vehicles—Electrical disturbances from electrostatic discharges.

MIL-A-17161D:1985—Absorber, radio-frequency radiation (microwave-absorbing material), general specification for.

MIL-HDBK-1512:1997—Electroexplosive subsystems, electrically initiated, design requirements and test methods.

MIL-HDBK-1857:1998—Grounding, bonding, and shielding design practices.

MIL-HDBK-235/1B NOT 1:2000—Electromagnetic (radiated) environment considerations for design and procurement of electrical and electronic equipment, subsystems, and systems.

MIL-HDBK-237B:1997—Electromagnetic environmental effects on platforms, systems, and equipment.

MIL-HDBK-274(1):1990—Electrical grounding for aircraft safety.

MIL-HDBK-293:1987—Electronic counter-countermeasures considerations in radar systems acquisition.

MIL-HDBK-294:1986—Electronic counter-countermeasures considerations in naval communication systems.

MIL-HDBK-335 NOT 2:1992—Management and design guidance, electromagnetic radiation hardness for air-launched ordnance systems.

MIL-STD-1310G:1996—Shipboard bonding, grounding, and other techniques for electromagnetic compatibility and safety.

MIL-STD-1377:1971—Effectiveness of cable, connector, and weapon enclosure shielding and filters in precluding hazards of electromagnetic radiation to ordnance, measurement of.

MIL-STD-1541A:1987—Electromagnetic compatibility requirements for space systems.

MIL-STD-1542B:1991—Electromagnetic compatibility and grounding requirements for space system facilities.

MIL-STD-1605:1973—Procedures for conducting a shipboard electromagnetic interference (EMI) survey (surface ships).

MIL-STD-220B:2000—Method of insertion-loss measurement.

MIL-STD-449D(1):1976—Measurement of radio-frequency spectrum characteristics.

MIL-STD-461E:1999—Requirements for the control of electromagnetic interference characteristics of subsystems and equipment.

MIL-STD-464:1997—Electromagnetic environmental effects requirements for systems.

MIL-STD-469B:1996—Radar engineering interface requirements, electromagnetic compatibility metric.

SAE-ARP1173:1994—Test procedure to measure the RF shielding characteristics of EMI gaskets.

SAE-ARP1972:1994—Measurement practices and procedures recommended for EMC testing.

Back to 2001 Annual Reference Guide Table of Contents